設備介紹
Equipment introduction
設備結構形式
1. Equipment structure
采用龍門橋式結構，運動為龍門架移動，如圖（參考）：
Adopting the gantry bridge structure, the movement is the gantry movement, as shown in the following figure (reference):
一.設備應用：
Equipment application:
檢測項目及技術要求
1. Test items and technical requirements
1.1觀察與測量TFT面板。
1.1 Observe and measure the TFT panel.
1.2使用時支持充氣分離產品與臺面。
1.2 Supports aerated separation products and countertops when in use.
1.3支持分區背光控制。
1.3 support partition backlight control.
1.3電動對焦：無極電子調速，提供精準對焦和快速對焦功能。
1.3 Motorized focus: Promise electronic speed regulation, providing precise focus and fast focus.
2.配置要求
2. Configuration requirements
此裝置采集圖像清晰可辨；
1) The image captured by this device is clearly identifiable;
此裝置可切換不同放大倍率（光學倍率25X,50X,100X,200X，500X,1000X）；
2) This device can switch between different magnifications (optical magnification 25X, 50X, 100X, 200X, 500X, 1000X);
此裝置使用尼康顯微光路，反射照明光源為高顯指LED照明；
3) This device uses Nikon microscopic optical path, and the reflective illumination source is high-indicator LED illumination;
此裝置測量系統精度可靠；
4) The accuracy of this device measurement system is reliable;
此裝置測量結果可設置輸出成指定文檔；
5) The measurement result of this device can be set to output as a specified document;
具充足保養、維修空間。
6) With sufficient maintenance and repair space.
操作人員動作記錄、存儲功能，方便管理人員對于故障的原因分析。
7) Operator action record and storage function, which is convenient for management personnel to analyze the cause of the fault.
二、設備主要技術參數
2. Main technical parameters of the equipment
| Type PG/面背光 Type PG/ face backlight |
| 75英寸：運動行程(mm) 75 inches: motion stroke (mm) | X:2000mm Y:1300mm |
| 調焦行程(mm) Focusing stroke (mm) | (Z軸)150mm (Z axis) 150mm |
| 測量與瞄準系統 Measurement and aiming system | 2/3"sony senser,數字彩色相機,2560*1920 2/3"sony senser, digital color camera, 2560*1920 |
| 視場外精度 Off-site accuracy | 3+（L/1000）um |
| 視場內精度 In-field accuracy | ±1um |
| 75英寸面背光 75-inch face backlight | 75英寸（3行4列可分區控制） 75 inches (3 rows and 4 columns can be partitioned control) |
| 反射照明系統 Reflective lighting system | 高顯指LED反射照明 High-definition LED reflective lighting |
| 透射照明系統 Transmission lighting system | 高顯指LED透射照明 High-definition LED transmission lighting |
| 工作高度 Working height | 850mm |
| 75英寸外形尺寸(mm)(長×寬×高) 75-inch form factor (mm) (length × width × height) | 3000*2200*1750 |
| 75英寸儀器重量（kg） 75 inch instrument weight (kg) | 約3600KG About 3600KG |
| 玻璃臺承重 Glass table bearing | 50kg |
| 儀器電源 Instrument power | 220V±10%（AC）50HZ |
檢測設備配置表
3. Detection equipment configuration table
| 序號 NO. | 品 名 Product name | 規格/品牌 Specifications / brand | 單位 unit | 數量 Quantity |
| 1 | CCD | 高清數字CCD HD digital CCD | 個 | 1 |
| Optical
system 2 | 光學系統 | 三目頭 Three heads | LV-TI3 Trinocular Eyepiece Tube CH (with Erect Image) | 套 | 1 |
| 目鏡 yepiece | Eyepiece CFI 10x / CN | 套 | 1 |
| Eyepiece CFI 10x CM Eyepiece with Crosshairs / CN | 套 | 1 |
| 鼻輪 Nose wheel | Nikon L-NU5A Motorized Universal Quintuple Nosepiece | 套 | 1 |
| 起偏器 Polarizer | Nikon YM-PO Polarizer for LV-U EPI | 個 | 1 |
| 檢偏器 Polarizer | Nikon L-AN Analyzer for LV-U EPI | 套 | 1 |
| DIC 棱鏡 DIC prism | Nikon L-DIHC DIC Slider | 套 | 1 |
| 物鏡 Objective lens | 5×、10×、20× CR、50x CR 、100x CR | 套 | 1 |
| 物鏡型號參數： Objective lens model parameters:
2.5X:Nikon CFI L Plan EPI 2.5X, (NA/WD : 0.075/8.80mm)
5X:Nikon CFI LU Plan FLUOR BD 5X (NA/WD : 0.15/18.0mm)
10X:Nikon CFI LU Plan FLUOR BD 10X (NA/WD :0.30/15.0mm)
20X:Nikon CFI LU Plan FLUOR BD 20X (NA/WD : 0.45/4.5mm)
50X CR:Nikon CFI L Plan EPI 50x CR (NA/WD : 0.70/3.9-3.0mm)
100X CR:Nikon CFI L Plan EPI 100x CR (NA/WD : 0.85/1.2-0.85mm) | | |
| 3 | 鼻輪 Nose wheel | Nosepiece controller: Nikon LV-NCNT | | |
| 4 | 光柵尺 Scale | 進口RENISHAW金屬光柵尺,分辨率0.0001mm Imported RENISHAW metal grating ruler with resolution 0.0001mm | 套 | 3 |
| 5 | XYZ軸傳動 XYZ axis drive | THK高精度直線導軌和THK研磨級滾珠絲桿 THK high precision linear guide and THK grinding grade ball screw | 套 | 3 |
| 6 | 驅動 Drive | Panasonic伺服馬達 Panasonic servo motor | 套 | 1 |
| 7 | 機臺本體 Machine body | 大理石 Marble | 套 | 1 |
| 8 | 光電限位 Photoelectric limit | 日本歐姆龍 Japan Omron | 個 | 6 |
| 9 | 操作軟件 Operating software | 定制 Custom made | 套 | 1 |
| 10 | 軟件 Software dongle | USB（內置于電腦機箱內） USB dongle (built into the computer case) | 個 | 1 |
| Industrial computer 11 | 工控電腦 | CPU: | Intel i7 | 個 | 1 |
| Memory: | 金士頓8GB Kingston 8GB | 條 | 1 |
| Hard disk caparity: | Western Digital 2TB(including auto backup disk) | 個 | 2 |
| Monitor: | LENOVO 21.5" LCD (FHD,Without Defect) | 個 | 2 |
| Keyboard: | LENOVO | 個 | 1 |
| Software: | Windows 7/L42:L44Anti Virus/Office2016(Excel, Word, PPT)Windows 7/Anti Virus/Office2016(Excel, Word, PPT) | 套 | 1 |
| 12 | 軟件使用說明書 Software instruction manual | 電子檔/紙質檔 Electronic file / paper file | 份 | 1 |
三、主要部件介紹說明
Main part introduction
1. 運動控制器
1.Motion controller
1.1集成了操縱盒搖桿控制功能。
1.1 Integrated joystick joystick control.
1.2提供軟件限位保護、機械限位保護以及光電限位三重保護功能。
1.2 Provide software limit protection, mechanical limit protection and photoelectric limit triple protection Features.
1.3采用一體式高度集成。服務極為方便，如果出現品質問題直接更換一個新控制器，全部解決控制問題，減少很多售后服務檢查時間，大幅降低客戶維修成本。
1.3 Adopting integrated high integration. The service is extremely convenient. If there is a quality problem, directly replace a new controller, all solve the control problem, reduce the inspection time of many after-sales services, and greatly reduce the customer maintenance cost.
2.顯微鏡機身
2. Microscope body
2.1高可靠性鏡架：為了進一步保證測量精度，載物臺基座采用高度耐用和防振動的鏡架。由于花崗巖的高穩定性，使測量可達到亞微米水平，同時確保的降低誤差
2.1 High reliability frame: In order to further ensure the measurement accuracy, the stage base adopts a highly durable and vibration-proof frame. Thanks to the high stability of the granite, the measurement can reach sub-micron levels while ensuring maximum error reduction
2.2 顯微鏡載物臺：一臺好的顯微鏡，不僅需要精確性和堅固性，而且還要能使這種品質得以長期保持。我們使用經長時間消應力處理的天然大理石，并通過使用線性導軌做引導機構，保證了顯微鏡載物臺的線性度。
2.2 Microscope Stage: A good microscope requires not only accuracy and robustness, but also the long-term maintenance of this quality. We use natural marble that has been subjected to long-term stress relief and uses a linear guide as a guiding mechanism to ensure optimum linearity of the microscope stage.
2.3 顯微鏡Z軸機構：此顯微鏡采用電動調焦功能，使用電動調焦可大幅提高操作性，并減少了進行聚焦時的操作疲勞?？刂坪锌梢园卜旁谧烂嫒我馕恢?，可以輕松實現粗調與微調之間的切換，同時還可以配備自動聚焦單元。
2.3 Microscope Z-axis mechanism: This microscope adopts electric focusing function. The use of electric focusing can greatly improve the operability and reduce the operation fatigue during focusing. The control box can be placed anywhere on the desktop, making it easy to switch between coarse and fine adjustments, as well as an autofocus unit.
3.照明系統
3. Lighting system
表面光：12V-15W高顯指LED燈箱
Surface light: 12V-15W high index LED light box
下光源：LED長壽命冷光源
Lower light source: LED long life cold light source
5. 工控機硬件配置及說明
5. Industrial computer hardware configuration and description
計算機系統采用IPC工控，具體配置如下：
The computer system adopts IPC industrial control, and the specific configuration is as follows:
CPU : 英特爾酷睿i7以上
CPU : Intel Core i7 or above
內存：8G DDR3
Memory: 8G DDR3
硬盤: 硬盤大于等于2T
Hard disk: Hard disk is greater than or equal to 2T
網卡：10/100/1000Mbit Giga LAN兩個以上
NIC: 10/100/1000Mbit Giga LAN two or more
I/O界面：4個USB 3.0（2個在面板，2個在背板）
I/O interface: 4 USB 3.0 (2 on the panel, 2 on the backplane)
2個PCI插槽，1個PCI-1插槽
2 PCI slots, 1 PCI-1 slot
2個COM口
2 COM ports
2個PS/2插孔
2 PS/2 jacks
MONITOR : 21”以上液晶顯示器
MONITOR : 21" or more LCD monitor
操作系統：中文簡體 Windows 7 PRO專業版
Operating System: Chinese Simplified Windows 7 PRO Professional Edition
Anti Virus 等防毒軟體。
Antivirus software such as Anti Virus.
Microsoft OFFICE 工具軟體
Microsoft OFFICE tool software
6. 軟件功能說明
6. Software function description
軟件功能簡介：
Introduction to software features:
(1) 測量元素種類齊全：
(1) Complete range of measurement elements:
能直接測量12種元素（點、直線、圓、圓弧、橢圓、矩形、槽形、○形環、距離、角度、開云線,閉云線）。能測量閉合云線的周長，面積及重心，使用三次插值算法，為目前最準測量云線的方法。采樣點越多，越精準。
Can directly measure 12 kinds of elements (point, line, circle, arc, ellipse, rectangle, trough, ○ ring, distance, angle, open cloud line, closed cloud line). It can measure the perimeter, area and center of gravity of closed clouds, and uses the cubic interpolation algorithm to be the most accurate method for measuring clouds. The more sampling points, the more precise.
尋邊算法，確保尋邊準確無誤.亞像素尋邊，精度可達像素的
Super edge-finding algorithm to ensure accurate edge finding. Subpixel search, precision up to pixel
1/10.有自動去毛邊功能，對陰暗不明的邊界一樣可以準確的找出.
1/10. There is an automatic deburring function, which can be accurately found for dark and unclear borders.
(2) 自動判別測量(自動識別線，圓，弧)
(2) Automatic discrimination measurement (automatic identification line, circle, arc)
只要將鼠標放在工件的邊緣上，即可自動尋邊得到線，圓或者弧.
Just place the mouse on the edge of the workpiece and you can automatically find the line, circle or arc.
(3) 顯示結果豐富
(3) Rich results
對各種元素的測量結果顯示﹐其信息量大﹐能滿足各種客戶的需要。并可設置哪些內容顯示,哪些內容不顯示﹐也可以單個元素進行單獨設置其顯示信息。也可對同類元素進行設置.
The measurement results of various elements show that the amount of information is large and can meet the needs of various customers.Want. And you can set which content is displayed, which content is not displayed, or you can enter a single element.The line sets its display information separately. It is also possible to set similar elements.
(4) 運行用戶程序時，可將數據自動對齊導入到Excel中.
(4) When running the user program, the data can be automatically aligned into Excel.
(5)輔助調光
(5) Auxiliary dimming
調光指示器,會指示用戶什么時候光強﹐避免了因打光所帶來的測量誤差﹐提高了測量精度和測量效率。
The dimming indicator will indicate when the user has the best light intensity and avoid the light.The measurement error has improved the measurement accuracy and measurement efficiency.
(6)標注功能：
(6) Labeling function:
能直接在繪圖區及影像區的元素圖形上標注角度、距離、X方向距離、Y方向距離、圓（弧）半徑、圓（?。┲睆?、弧長。
The angle, the distance, the X-direction distance, the Y-direction distance, the circle (arc) radius, the circle (arc) diameter, and the arc length can be directly marked on the element graphics of the drawing area and the image area.
(7)系統誤差修正：
(7) System error correction:
軟件帶有系統誤差修正功能。目前可進行線性，區段補償，垂直度誤差補償，扭擺誤差補償(特別對大行程，移動滑架式機器有用)，Z軸直線度誤差補償，鏡頭中心偏移誤差補償。
The software comes with a system error correction function. At present, linear, segment compensation, verticality error compensation, torsion pendulum error compensation (especially for large strokes, moving carriage type machines), Z-axis straightness error compensation, and lens center offset error compensation are available.
(8)公差
的尺寸公差計算能力?？稍O(shè)置默認的公差帶符合國標的形位公差計算能力，能計算形狀公差，真直度，圓、 弧的真圓度。位置公差計算包含位置度、平行度、垂直度、傾斜度及同心度﹐對稱度。超差能自動報警，并以紅色警示。
Complete dimensional tolerance calculation capability. The default tolerance bａnd can be set to meet the national standard shape tolerance calculation ability, and can calculate the shape tolerance, true straightness, circle, and arc roundness. Position tolerance calculations include position, parallelism, perpendicularity, inclination and concentricity, and symmetry. The out-of-tolerance can automatically alarm and be alerted in red.
(9) DXF檔導入編程
(9) DXF file import programming
DXF圖檔導入，自動產生名義值，并自動產生工件的測量程序。測量完成后，可進行測量值和名義值的比對。(11)一次測量多個相同工件(陣列測量)提供多個相同工件放置在工件臺，可以一次性測量完成所有的工 件，這就是陣列測量。軟件提供矩形陣列和環形陣列功能。矩形陣列就是工件在水平和垂直方向呈規律放置。環形陣列就是工件繞著某點旋轉，呈環形狀態。并自動將測量數據導出到報表及SPC軟件中.
The DXF image file is imported, the nominal value is automatically generated, and the measurement program of the workpiece is automatically generated. After the measurement is completed, the comparison between the measured value and the nominal value can be performed. (11) Measuring multiple identical workpieces at a time (array measurement) provides multiple identical workpieces placed on the workpiece table, and all workpieces can be measured in one measurement, which is the array measurement. The software provides a rectangular array and a circular array function. A rectangular array is where the workpieces are placed regularly in the horizontal and vertical directions. A circular array is a workpiece that rotates around a point and is in a ring shape. And automatically export measurement data to the report and SPC software.
四、機臺動力環境
Machine power environment
1. 機臺適用環境條件
1. Machines apply to environmental conditions
工作環境溫度：(20±3)℃ 濕度60%～90%
Working environment temperature: (20 ± 3) ° C humidity 60% ~ 90%
潔凈度 ：100～100K
Cleanliness: 100～100K
噪音 ：75db以下
Noise: below 75db
振動：機房不要建在有強振源、高噪聲區域，如：附近有沖床，壓力機，鍛造設備，打樁機等
Vibration: The machine room should not be built in areas with strong vibration sources and high noise, such as: punching machines, presses, forging equipment, pile drivers, etc.
磁場、電場 ：不要建在強電場、強磁場附近，如電源斷電設備、 變壓器、電火花加工機床、變頻電爐電弧焊及滾焊機等；以及高粉塵區、腐蝕性氣體源附近。對于有害氣體車間，必須布置于有害氣體車間的上風。
Magnetic field, electric field: Do not build near strong electric field and strong magnetic field, such as power supply equipment, transformer, EDM machine, variable frequency electric furnace, arc welding and seam welding machine; and dust area, corrosive gas source. For hazardous gas plants, it must be placed in the upper hａnd of the hazardous gas plant.
2. 系統動力
2. System power
電源(單相）：(220±5)V/50-60HZ/4A 總功率：800W
Power supply (single phase): (220 ± 5) V / 50-60HZ / 4A Total power: 800W
工廠必須為設備提供至少第三種接地裝置。
The factory must provide at least a third type of grounding device for the equipment.
